Відео

' and then you will start yelling obsenitys ' yup!

Awesome job! Do you have a site to order?

You can also secure the knife down with clear wire on the top and bottom of the handle. Just see through the foam board

Good job looks great

I tend to do this. I have a hobby for arts and crafts and some wood work. May I suggest to use hot glue for patches and a pin for reenforcement. Pins and staples for the jacket. Elmers glue isn’t suffice for thick material. Just a suggestion.

Great Video but I was on the edge of my seat so scared for your fingers... Safety first my man, safety first. Push sticks are your friends.

Omg thank you! I was worried I was going to have to get rid of my ice machine that I love your tutorial was fantastic. I was able to take my machine apart and clean it extremely well. I appreciate it thank you.

“I also took the rubber bushings and flipped them, so the new side would be facing out” Me:🤯🤯🤯🤯🤯🤯 wouldn’t even think of that.

The only thing I would do different is the bottom of the drawer that is probably 1/8 to 1/4 thick should slightly protrude into the face of the drawer a 1/4”. To make sure the bottom is secure. Great instructional video.

Hi Jon, how wide is your base plate?

2 yards were enough for all 5 chairs?

I love tutorials that don't have 10 minute intros. Thank you for not wasting time!

Tyvm single has fix stuff myself ❤

Best step by step ever! Thank you! 🎉

Nice! For the future, the Crome handles on the draws slide right off to the sides. Saves the time tapping them off. Great restoration!

You didn’t test to see if the power was still off?

How available

Your Video is GREAT !!! very clear, concise, to the point

Hi great work! Question how did you attatch the coins to the backing? Ty.

Thank you so much for video! Taking the top off was driving me crazy

Excellent directions! Even “the wife” could follow them successfully.

it looks great but its kind of a shame to destroy the jacket and belt.

What is the dimensions of the wood we are using?

I found the dewalt trimmer line to be pretty garbage but this video is A+

Thanks! Found marketplace toolbox $15 that’s dirty and little paint chip. Originally red so will have to paint everything black to match my other table but you pointed me to the right direction. Sand, clean, primer, paint. Guess I would do little extra and put 2k clear over it

Great video. Should be easy to follow. Are those 3/4 inch boards you are using?

I have a question for you plz My grill knobs not moving right The grill is working but temp is less than 350 f The knobs moving but looks like not connected to the valves some how Do you have a solution?

GREETINGS, thank you so much, hey, I LIKE that house too😊

GREETINGS, thank you so much, hey, I LIKE that house too😊

GREETINGS, thank you so much, hey, I LIKE that house too😊

Just got my speed booster installed on my 2015 Acura and it’s a whole different car

Great Job!! 👍

John you the man

your going to lose a finger some day....

fingers crossed. I have been in wee wacker hell.

OMG! I have the original opal (like from the kickstarter) and it has always screeched. I was able to fix it following your video! Only thing I did differently was add some food safe grease to the top and bottom of the auger. And I had only one extra screw. :)

The screws have rusted to dust on my spindle shield. I've tried to push it off lightly with a flathead screwdriver, but I'm afraid it'll break. It's not budging. I was thinking of spraying WD40 in the holes next. Any ideas for a way to get it off now, please?

I'm VERY grateful you didn't draw this video out to 20 plus minutes. You are AWESOME.

I seats are folded down and I can’t get them to go back up any advice?

Thank you!

Thanks, Bro!

Great Video. I watched over a dozen videos. This is the only one that has the knob on the head like mine. I was able to replace the line quite easily once I knew how to do it. I have saved the link for when I replace the line again. Likely 10 years down the road. Thank you for the easy to follow steps and directions.😁

Thank you for this was stuck in a rut trying to read the manual and do it that way.

Dude…this is why I only buy from Costco. Just take it back and get a new one.

Did you have to buy a new lock and key? I need a new set for my tool box just like this one you refinished. Do you know where I could buy a new lock and key

Very nice! Thanks

Whaaaaat? You bump the head to lengthen the string?!

Both lines are wound the same direction?

fucking thaaank you, every other video i see has the other style of bump rotor. hard to find this one for some reason!

Excellent job